ABex System Modules

KT-TM-ISO-Amp Isolation Amplifier

The TM-ISO-AMP is a is a ABEX Terminalmodul to interface 2 isolated input amplifiers and 2 isolated output amplifiers to the analog backplane. There is also the possibility to switch the Signals directly to a PXI DMM. 2x IN and 2x OUT Isolation Amplifiers with 1000V galvanic isolation.

 

more

KT-TM-MultiCON Multiconnect to AB / CECO

The TM-ISO-AMP is a is a ABEX Terminalmodul to interface 2 isolated input amplifiers and 2 isolated output amplifiers to the analog backplane. There is also the possibility to switch the Signals directly to a PXI DMM.

 

more

KT-TM-BSCAN-GOEPEL

The TM-BSCAN-GOEPEL is a ABEX Terminalmodul for the Göpel Boundary Scan Controller SFX/PXI 1149-FXT. It is connected to the BSCAN-Controller with an onboard Adapter-Paddlecard. The TM-BSCAN-GOEPEL routes all signals from the Göpel BSCAN-Controller directly to the ABEX front connector. For the differential to Single-Ended conversion, external TAP-Interface Cards TYP 02 (TIC02)- from Göpel are necessary.

 

more

KT-TM-BSCAN-JTAG Baseboard

Baseboard for JTAG JT2147/ABEX, Terminal Module for JTAG PXI BSCAN Cards, Carrier for JT2147/ABEX.

 

more

KT-TM-62x1 Multifunction

The TM-62x1 Multifunction is a ABex Terminal Module and is intend to use with a PXI-6221 or PXI-6251 measurement card in an Abex System. It expands the analog inputs and outputs on the measurement cards to a wider voltage range. The module has several signal conditioning units for the resources of the measurement card.

 

more

KT-TM-403 DIG50IO Universal Pin Electronic

The DIG50IO is a 20 channel universal digital and analogue card for the ABex System. It can be used as digital pin, pmu and power supply.

  • 20 full bidirectional channels each channel can be either input or output
  • Levels and thresholds programmable per channel
  • High-Speed-Pattern with up to 50 MHz
  • High voltage range (-4V .. +13V) also for pattern
  • Active and passive load per channel (active load up to 24mA)
  • Full 4-quadrant operation in PMU Mode (sourcing and sinking)
  • Up to 200mA per channel, also usable as DPS
  • Data deskewing, enable and comparator, adjustable slew rate
  • „OnChip“ calibration calculation
more

KT-TM-404 86x4 Switching Module

The TM-404 Matrix from Konrad Technologies is intending to use to connect test points and measurement devices. This sould be local or over the ABex Bus. On the back it can be plugged in front of a PXI-501 card (ICT) from Konrad Technologies. The module could be also used stand alone. The Module could be configured to 4 or 8 Busses. The Matrix busses could be connected to the ABex Bus.

 

more

KT-TM-405 Utility

The KT-TM-405 Utility is a Terminal Module for the ABex-System. It provides 5 galvanic isolated supply voltages for TUA (Test Unit Adapter) supply. Each output is protected against over current. The outputs can be enabled and disabled individually. The Module also has an inhibit-signal on the front connector which must be shorten to enable the module. The power good signals of all supply voltages can be read back with the ABEX System-Controller.

 

more

KT-TM-501 2xAO -10V... +40V, Shunt I-Meas

The TM-501 from Konrad Technologies is an Abex Terminal Module that extends the Multifunction measurement card PXI-501 with additional features. It is located in Front of the PXI-501 card. It expands the analog outputs on the measurement cards to a wider voltage range. The module has several signal conditioning units for the resources of the measurement card.

 

more

KT-TM-4070 DMM Terminal Module

ABex terminal module for adaptation of the 6,5 and 7,5 digit PXI-407x DMM from National Instruments. The terminal module TM-4070C has been developed to be used in the ABex system. Its intended use is the connection of the digital multimeter NI PXI-407x with the ABex analog bus for current, voltage and resistance measurements. Signal connections can be programmed via the front connector and the ABex analog bus.

 

more

KT-TM-6363 for PXIe-6363

The TM-6363 is a ABEX Terminalmodul for the National Instruments Multifunction card PXI-6363. The TM-6363 routes all signals from the National Instruments PXI-6363 card directly to the ABEX front connector. Additionally, a SMU (National Instruments PXI-4132) can be connected to the card with the cable KT-WIRE-4132. These signals are also routed to the ABEX front connector.

 

more

KT-TM-6528 Digital I/O Terminal Module

The terminal module KT-TM-6528 is used together with the following PXI boards from National Instruments:

  • NI-PXI-6528:Digital I/O board: 
    24 inputs, 24 outputs, 0-60V
  • NI-PXI-6508:Digital I/O board:
    96 TTL I/Os, direction per 8-Bit port defineable
  • NI-PXI-6509:Digital I/O board: 
    96 TTL I/Os, direction per 8-Bit port defineable, 24mA
more

KT-TM-SMU-4130

The ABex SMU-4130 is a universal terminal module for the ABex system to route signals from a NI-PXI SMU device to the front connector of the ABex. There is a 12V / 60W power supply on board to support NI SMU with external power requirement.

KT-TM-SMU-4132

The ABex SMU-4132 is a universal terminal module for the ABex system to route signals from a NI-PXI SMU device to the front connector of the ABex.

KT-TM-Flashrunner

The ABex TM-Flashrunner is a terminal module for the ABex system to route signals from the PXIFRA3 Flashrunner card from SMH to the front connector of the ABex. The terminal modules features relays on each line to disconnect the flasher from the DUT. This is used for example when an ICT like the LEON system by Konrad Technologies is connected in parallel to the flasher connections.

ABex TM-ME-9000

The ABex TM-ME-9000 is a passive terminal module to route the signals from the PXI cards listed below to the ABex front connector:

  • Meilhaus ME-9000p/8 RS232 cPCI (8x RS232)
  • Advantech MIC-3680/3 (2x CAN)
  • EKF CB2-1-PIPE (4x USB 2.0)

KT-TM-MultiCON

The ABex TM-MultiCON is a universal terminal module for the ABex system to route signals from a PXI device to either the ABex bus or the front connector of the ABex. The signals routed to the ABex bus can be switched individually.

KT-TM-LVDS

The ABex TM-LVDS is a group of modules that provides functionalities for receiving (RX) and sending (TX) data via MIPI (Mobile Industry Processor Interface). The module currently supports two different chipsets from Maxim (GMSL) and TI (FPD-Link III). Internally, data is transmitted as MIPI CSI2 (Camera Serial Interface) on a physical layer D-PHY.

 

The ABex TM-LVDS is composed of the following modules:

  • ABex TM-LVDS baseboard
  • RX/TX modules with TI or Maxim Chipsets

KT-TM-Göpel-61xx

The ABex TM-Göpel-61xx is a passive terminal module to route the signals from the Göpel PXI 61xx PXI cards to connectors on the ABex frontpanel.

ADAS Virtual Test Drive